Honda   Honda Outboard Parts
Honda Outboard Forum Honda Outboard Parts Discussion Forum Honda Outboard Parts Boat Parts Honda Outboard Forum Outboard Motor Parts Contact Us
Honda Parts

Go Back   Honda Outboard Forum > Members List is offline

Super Moderator

Visitor Messages

Showing Visitor Messages 1 to 10 of 10
  1. Rustycanon
    08-18-2016 07:36 PM - permalink
    got cut off on the phone earlier and phone lines are now down can you lok at my post from two days ago please Rustycanon
    07-23-2016 11:33 AM - permalink
    I'm replacing a head gasket on a 2009 Honda 150 dust didn't want to send out cyl head to machine shop I started eng and noticed crankcase filled with water I changed oil prior to starting eng where is it possible water could of enter eng ? Can u please reply thk u
  3. Safetystop
    05-03-2016 04:29 PM - permalink
    I am reassembling a Honda 9.9 (BABJ 1606701). Can you tell me the torque values for the Cylinder head bolts and the Cylinder Block to Oil Pan bolts? I would also like to know how to align the cam gear and flywheel timing marks. When I disassembled the engine, no matter how I turned the crankshaft, I could not align the marks in any manner that looked appropriate even though the engine was running fine and smooth prior to disassembly.

    Thanks, Safetystop
  4. Capt Bob Pastor
    12-19-2014 05:21 AM - permalink
    Capt Bob Pastor
    I have twin 2006 BF150's. The fuel data (gph, total) works for the sb motor but not for the port motor. I already have the shop manual for my motors but it does not have a rigging guide. I see you posted a page for the harness back in 2012 which refers to page 16-2 and 16-3 for dual/3 motor connections. Those pages don't show anything like that in my manual. Do you have a rigging manual for the speedo/harness?
  5. ante.botica
    01-14-2014 12:10 PM - permalink
    Hi there,
    I have a question, and from they reffered me here, i hope you could help. I have a outboard honda 4,5 BF engine, and need to order few spare parts. problem is there is no honda 4,5 offered as engine number. at several other places i read that honda 5 parts are compatible to those of honda 4,5. At i found HONDA BF 5 AKO LA as the closest engine to mine, so I wanted to check with you if parts of honda bf 5 ako la will match my honda bf 4,5.
    Thank you in advance.
    Forward Message
  6. lousy mechanic
    02-03-2013 11:49 PM - permalink
    lousy mechanic
    hi thanks for tips the carbs were clogged main jets works fine now looking to install kicker motor with handheld remote can they be installed on motor with tiller handle?
  7. lousy mechanic
    01-25-2013 02:17 PM - permalink
    lousy mechanic
    Hi thanks for tips so far...on my 75HPBF75A 1997 with only 167 hours on it but sitting outside unused for 12 years Replaced waterpump now fuel is not getting to spark plugs carbs are not gummed up and look great inside have compression please what else can be wrong????? thankyou
  8. Gerry Schey
    11-22-2012 10:57 PM - permalink
    Gerry Schey
    Have 2010 135stalls when I go into neutral. New plugs.any thoughts. TY
  9. rhanipnr
    10-15-2011 11:33 PM - permalink
    My '98 bf90a developed a bog and stall when accellerating. We set all to manual specs but while doing so developed an irregular sputter between 1200 and 3000 rpm. As we adjusted the carbs in and out the bog got some better but the sputter remained. Recently replaced a clean fuel filter and plugs. Any thoughts ?
  10. cj7ngolf
    09-23-2010 04:44 PM - permalink
    Need to get rid of anyhorish and there is another one too, I reported them both and nothing has been done...

About Me

  • About
    Lake Placid, Fl
  • Signature
    Honda Outboard Parts


Total Posts
Visitor Messages
General Information
  • Last Activity: 11-20-2017 08:25 AM
  • Join Date: 02-23-2006
All times are GMT -5. The time now is 08:37 PM.

Outboard Parts

Other Forums
Yamaha Parts
Suzuki Parts
Evinrude Parts
Johnson Parts
Mercury Parts

Copyright 2000 - 2017, Outdoor Network LLC